For a project I'm working on, I'll have a Raspberry Pi sitting behind a 4G LTE modem:
This modem is on AT&T's network, but regardless of the provider, unless you're willing to pay hundreds or thousands of dollars a month for a SIM with a public IP address, the Internet connection will be running behind CG-NAT.
What this means is there's no publicly routable address for the Pi—you can't access it from the public Internet, since it's only visible inside the cell network's private network.
There are a few different ways people have traditionally dealt with accessing devices running through CG-NAT connections:
- Using a VPN
- Using a one-off tool like ngrok
- Using reverse tunnels, often via SSH
And after weighing the pros and cons, I decided to go with option 3, since—for my needs—I want to have two ports open back to the Raspberry Pi:
- Port 22, for SSH access
- Port 80, so I can serve HTTP traffic
Security Warning: Punching a hole through to any network—especially to expose something like a Raspberry Pi to the public Internet, increases your network's attack surface. You're responsible for your own security, and if you don't have a good grasp on fundamental Linux and SSH security, you might not want to do this.
Prepare a VPS as a Tunnel Server
Paid services like VPNs and ngrok run their own servers, but can cost upwards of $10-20/month if you want to run a lot of traffic through them. Sometimes they are easier for specific needs, but as I mentioned, I just wanted two open ports.
So I chose to use one of my existing DigitalOcean VPSes for the task. I pay $5/month for it, use it to host some websites, and it also gets assigned a static public IP address, so I can point a domain at it, like
On that VPS, I needed to configure SSH so it could work as a tunnel server:
AllowTCPForwarding option must be set to
yes for this to work—and that's the default. But you can confirm this with
You will need to configure the
GatewayPorts option, so edit the SSH config file:
$ sudo nano /etc/ssh/sshd_config
And add the following line at the bottom:
Save your changes, and restart SSH:
$ sudo systemctl restart ssh
Confirm both settings are
$ sshd -T | grep -E 'gatewayports|allowtcpforwarding' gatewayports yes allowtcpforwarding yes
Security Warning: For better security, you can set
GatewayPorts clientspecified, and then specify certain IP addresses allowed to connect. Or, you could restrict access to
GatewayPorts no—that way only users who are logged into the tunnel server could access the Raspberry Pi via SSH.
Prepare the Raspberry Pi
The Raspberry Pi will need to be able to connect to the VPS via SSH, so you should create an SSH key pair for this purpose. On the Raspberry Pi, run:
$ ssh-keygen -t ed25519 -C "my-raspberry-pi-name"
Then press enter for all the prompts. This should create a public SSH key located at
/home/pi/.ssh/id_ed25519.pub. Get the contents of that file by copying the output of:
$ cat /home/pi/.ssh/id_ed25519.pub
Now, log into your tunnel VPS, edit the
~/.ssh/authorized_keys file, paste the public key you just copied into a new line, and save that file.
At this point, you should be able to SSH into the VPS from your Raspberry Pi. Test it with:
$ ssh my-username@my-vps-hostname-or-ip
You'll be prompted to accept the host key, so type
yes when prompted, and you should be logged in. Go ahead and log back out (type
Set up the tunnel
Now, it's time to test if tunneling works. First, on the Raspberry Pi, run this command to configure a tunnel over the IPv4 interface between port 22 on the Pi to port 2222 on the VPS:
$ ssh -nNTv -R 0.0.0.0:2222:localhost:22 my-username@my-vps-hostname-or-ip
This will output a bunch of debug information, and eventually show:
... debug1: Entering interactive session. debug1: pledge: network debug1: client_input_global_request: rtype email@example.com want_reply 0 debug1: remote forward success for: listen 0.0.0.0:2222, connect localhost:22
Leave that terminal session running, and in another, log into the VPS and test logging into the Pi from it:
$ ssh -p 2222 pi@localhost
If you have password login disabled like I do, you might get a prompt like:
pi@localhost: Permission denied (publickey).
But that's okay—the important thing is you should see more
debug messages in the Pi's terminal—if you do, that means the port forwarding is working.
Now, for the big test: check if you can SSH directly into the Raspberry Pi from your own workstation (not logged into the VPS) through the VPS tunnel:
$ ssh -p 2222 pi@my-vps-hostname-or-ip
And bingo! You should be in. But if not...
There are a few things that could be going wrong:
- Check SSH's current configuration with
sshd -T | grep -E 'gatewayports|allowtcpforwarding'— make sure the two settings configured correctly. If the sshd config file is correct, make sure you restart SSH to make the changes take effect (
sudo systemctl restart ssh).
- If you have a firewall configured on the server (
firewalld), make sure the ports are open through which you're connecting!
- Triple check open connections with
netstat -tulpn— in one case, I hadn't set
GatewayPortscorrectly, so when I ran that command, I saw a listing for
127.0.0.1:2222, meaning the forwarded port was only accessible if logged directly into the VPS. It should be showing as
0.0.0.0:2222if you set up everything according to this guide.
This is great if you just want to connect through to the Pi once, but if you want a persistent connection resilient to network dropouts, you will need to run something like
It's easiest to install it via
$ sudo apt install autossh
autossh doesn't come with any automatic service integration, so you need to create a systemd unit file and defaults manually.
Create a file to store autossh defaults, with
sudo nano /etc/default/autossh, and put the following inside:
AUTOSSH_POLL=60 AUTOSSH_FIRST_POLL=30 AUTOSSH_GATETIME=0 AUTOSSH_PORT=22000 SSH_OPTIONS="-N -R 2222:localhost:22 my-username@my-vps-hostname-or-ip"
Note: You can add multiple ports in the
SSH_OPTIONSline—just add in an additional
-R 8080:localhost:80after the first port 22 statement, and you'll be sharing the local HTTP port over the remote server's port
autossh systemd unit file
Create a file to tell systemd about autossh, with
sudo nano /lib/systemd/system/autossh.service, and put the following inside:
[Unit] Description=autossh Wants=network-online.target After=network-online.target [Service] Type=simple User=pi EnvironmentFile=/etc/default/autossh ExecStart=/usr/bin/autossh $SSH_OPTIONS Restart=always RestartSec=60 [Install] WantedBy=multi-user.target
Save that file, then symlink it into place so systemd can discover it:
$ sudo ln -s /lib/systemd/system/autossh.service /etc/systemd/system/autossh.service
All that's left is discovering the new systemd unit, and starting the service:
$ sudo systemctl daemon-reload $ sudo systemctl start autossh
If everything's working (you can log in from your own workstation through the VPS tunnel server), you can set autossh to run at system boot:
$ sudo systemctl enable autossh
If you have any problems, run
journalctl -u autossh to view the logs.
There are myriad ways of making a Pi accessible through CG-NAT, including VPN solutions like Wireguard (e.g. with Pi-VPN), Tailscale, Zerotier, etc.—however, if you already have a VPS running somewhere, and know SSH pretty well, SSH tunnels are a nice, simple, secure solution, at least for small scale deployments.
You may also not need
autossh at all—later versions of OpenSSH include some of the features of
autossh built-in, and you could just use
ssh + systemd to keep a connection alive. For more on that, see these two posts: